Loading...

A fully integrated suite of configuration and visualization tools for all Haply devices.
the panel or switching device after an unsaved change asks to Save, Leave without saving
or Stay; Apply and Save… stay pinned at the foot of the panel with a note while changes wait,
and one confirmed Save… lists what goes to the device and what the Hub keeps.
device, a Starting position section has one button: Clutch freezes the Freeform tool at
once, you move the device to where you want to start, and Save (or grip A) keeps it as the
app's starting position for that device; the 3D view shows the frozen point and the new start,
the section warns when a zoom or rotation will be stored too, and it offers Reset and
Clear.
(service 3.5.8), navigation can be saved as an app's starting position without moving the
cursor, and the panel shows the mount and the navigation in one 3D view.
VerseGrip's button hold (turn on Show advanced settings).
within about two seconds (service 3.5.8), and handedness and gravity compensation changes now
reach every other app holding the device.
VerseGrip has its new 3D model and demo previews show only the scene; a VerseGrip firmware update
confirms instead of reporting a failure, pie zoom and the clutch only move the app you are using,
the Clutch navigation shortcut keeps working in Freeform, Freeform starts centered on a stock
Freeform, and some grips no longer flicker in the device list.
and service 3.5.8). The wizard pairs a wireless VerseGrip with its dongle over the VerseGrip's
USB cable or, with no cable, by holding the VerseGrip's Calib + User1 buttons (VerseGrip firmware 1.4.0
or later). It lists its stages, explains failures, resumes if you close it mid-run and suggests
pairing again when a device was left on another network. One dongle follows one VerseGrip: pairing
replaces the VerseGrip paired before.
mount, a ghost of the navigated device, diamonds on the mount and navigation origins, and rulers
that show a value only for the axis you are working on. The navigation itself is never saved.
into the mount without moving the cursor; the Save as defaults shortcut bakes it into the
mount and saves it as the app's starting position. A banner above the tabs makes the button easy
to find, and with Auto Apply off, Navigation edits wait for Apply so you can tune them while the
device drives the mouse.
(service 3.5.8); older services show a hint to re-apply the preset after rotating.
link to the device mount rotation in the Settings tab.
follows the selection or stays on the device; a toolbar toggle that is remembered. _If you relied
on the camera holding the view, turn Camera follow off._
after Leave without saving, leaving again without a new edit does not ask; a value the device
holds and has not stored yet opens the Save… dialog instead. _Every Inverse3 user who edits
settings will see it._
and changes wait.
and the badges' Store on device…: a dialog lists what goes to the device as its power-up
defaults and what the Hub keeps (Return to home), warns before the device is written and stores
once. The device stores the mount itself (service 3.5.6 or later; firmware 7.10.1 or later keeps
it through a power cycle), every field obeys Auto Apply, and Modified and Reset to default
compare against what the device boots into, handedness included (service 3.5.7 or later). _Every
Inverse3 user who saves settings will see the new dialog; a mount you relied on the Hub
replaying must now be stored with Save…._
your typed value, and a value applied from the Hub is not snapped back by its own echo. Needs
service 3.5.8 and device firmware that reports its changes.
the device, a Starting position section has one button: Clutch freezes the Freeform tool,
you move the device to where you want to start, and Save (or grip A) keeps it as the app's
starting position for that device. The 3D view shows the frozen point and the new start, a
warning says when a zoom or rotation will be stored too, Reset drops a detected navigation,
and Clear puts the device's default Freeform position back. _The footer's Clear all saved
fields now also clears this saved starting position and restores the default one while Freeform
runs._
link for 1.5 s and closes when you leave; no toggle, and at phone width it never expands. _Rest
the pointer on a link to open it._
the four rotation tooltips tell one story (the device's own orientation moves with the device,
the session rotation is an offset on top).
x10 field per axis (service 3.5.8 accepts values below x1). _A saved scale of 0, above 10 or
negative is corrected on replay; a saved 100 replays as 10._
menus; selectors in field headers are compact, and one Euler / Quaternion choice is remembered
for every rotation field.
(service 3.5.0 or later): other apps see the change at once, choosing the handedness the device
already has is no longer an error, home return now also reaches a Minverse, and a write the
service refuses shows its error.
tracing Haply-logo spinner while a scene loads, the same back button as the device panel, and a
fade between pages.
Later) and reopens the update banner from its Hub row. _Click the update icon to open it._
events that ended more than a day ago are no longer listed; the Navigation Modes tutorial is no
longer listed and Getting Started ends at Point with a VerseGrip; the Service page accepts
decimals for fractional settings.
way back to 1× and below, and the step in use is highlighted from the live scale. _The 3× step
is gone; pick 2× for the largest._
to freeze the cursor while you move the device.
Bugs that were present in 1.5.0.
_If you drive two apps at once, zoom or recenter from the pie in each._
device mount, the rotation lock and Transfer rotation to profile are gone, and the session
rotation is editable again. See _Before you upgrade from 1.5.0_ below.
changes it later.
Overview and Input Control; an older or busy service renders instead of throwing.
shortcut set to Allow everywhere went dead; it now works while a Freeform session runs, and
its row reads "Active only while a Freeform session is running".
machines with a changed Freeform workspace size; they are re-tuned. _A device with no saved
starting position starts from a new place, and a MinVerse's workspace is at scale 1 instead of
1.5._
does (firmware 7.5.0 or later).
One warning stands above the rest: if a saved app profile holds a mount rotation and your device
mount is active, that rotation now applies on top of the device mount at app start. Under 1.5.0
the Hub ignored it while the device mount owned the rotation, so the workspace can turn a second
time. The Hub warns once per saved entry; dismiss it if the rotation is deliberate, otherwise
reset that saved rotation to its default and save again.
Also small: the "In use by another program" overlay is gone (the device panel no longer blurs the
3D view while another app holds the device); clicking a badge now hides that
kind of feature.
None.
a non-cabled VerseGrip's firmware before pairing, so on older firmware the run fails; pair over the
cable instead.
"Save as PDF" in that dialog for now.
and Save writes only the device you save on; the other device's move during the freeze stays live
and unsaved.
with the starting position (the section warns before you save): zoom to 0.5×, save, zoom to
0.5× again, save, and the stored scale is 0.25. What Save should do with the zoom is still to
be decided.
default start positions; the Hub does not warn about it yet.
All available downloads for this release: